How Can You Make Copper Stay Blue After Heating

Download Article

Download Article

Annealing copper makes it softer and less brittle, which allows you to bend it without breaking it. This malleability allows you to hammer and mold the copper into any shape you wish without cracking the metal. You can anneal any grade and thickness of copper as long as you have a flame that can transmit enough heat to the metal. The most straightforward way to anneal copper is by heating it with an oxygen acetylene torch and rapidly cooling it in water.

1. 1

   Put on a pair of safety goggles before you handle the torch. Wearing safety goggles is a necessary precaution to ensure eye safety anytime you are working with open flames. Wear a pair of goggles that are rated to at least shade 4 to adequately block the bright acetylene flame from harming your eyes.^[1] If you don't wear safety goggles, you could risk seriously damaging your eyes by looking directly at the acetylene flame.

   • Goggles used for annealing, arc cutting, and welding are rated on a scale of 2–14, with 2 as the least tinted and 14 as the most tinted. Since an acetylene torch is much less bright than a welding torch, your eyes will be protected by relatively lightly tinted glasses.
   • If you do not own a pair of safety goggles, purchase a pair at a large hardware store or a welding-supply store.

2. 2

   Connect 1 hose to each tank to set up the acetylene torch. The torch itself—which will produce the flame—will have 2 hoses coming out of it. Connect the red welding torch hose to the acetylene tank, and the black hose to the oxygen tank. The acetylene gas will start the flame and the oxygen will continue to feed the flame once it's lit. You'll also adjust the amount of oxygen coming from the tank to control the intensity of the flame.

   • Before you begin, make sure that the 2 pressure gauges on the oxygen tank and the 2 pressure gauges on the acetylene tank are all at "0."^[2]
   • If you don't already have an oxygen acetylene torch, you can purchase or rent one from a large hardware store or a home-improvement store.

   Advertisement

3. 3

   Turn the acetylene valve a quarter turn clockwise. This will engage the gas tank and switch on the flow of acetylene to the regulator. Only turn the valve a quarter of a turn to ensure that there is enough acetylene to start the flame, but not so much that it will be too large to control. Keep an eye on the pressure valve and fine-tune the acetylene valve until it reads 7 psi (pounds per square inch).^[3]

   • You'll find the pressure gauge directly on top of the large acetylene tank. Look for the dial that is marked "pressure" or "psi."
   • Once the flame is burning consistently, you can adjust its intensity by turning the acetylene-tank valve so it's more or less open. Find the tank valve on top of the acetylene tank. In most cases, it will be next to (or even attached to) the pressure gauge.

4. 4

   Turn the valve on the oxygen tank as far as it goes counterclockwise. Once the oxygen tank valve is fully on, adjust the line pressure by turning the oxygen tank regulator knob clockwise. Take a look at the regulator gauge on the oxygen tank to make sure that it's at 40 psi. If it's not, fiddle with the regulator knob until the gauge reaches the desired pressure.^[4]

   • The oxygen-control valve will be a handle located on the top of the oxygen tank. It may have a directional arrow indicating which way is "on."
   • A correct mixture of oxygen to acetylene is crucial to produce a hot, manageable flame.

5. 5

   Light the acetylene torch with a flint striker. To light the flame, hold the acetylene torch in 1 hand and turn the acetylene knob (on top of the gas tank) a half-turn clockwise with your other hand. This will start the flow of gas. Hold a flint striker about ¹⁄₂  in (1.3 cm) away from the torch head. Spark it repeatedly until you see an orange-red flame.^[5]

   • Once you've turned on the acetylene gas knob, don't wait more than 2–3 seconds to pick up the striker once the gas is flowing, as it's incredibly flammable.

6. 6

   Turn the oxygen valve until the flame turns blue. Once a bright orange flame is coming out of the tip of the torch, turn the oxygen valve on the side of the torch clockwise to introduce oxygen into the burning acetylene. Continue turning the knob until the flame turns blue.^[6] A blue-colored flame indicates that the flame is at the ideal temperature for annealing copper.

   • Turn on the flow of oxygen slowly, so the flame doesn't suddenly flare up.
   • A flame that is too hot will burn the copper, while a flame that is too cool will not be strong enough to change the copper's properties like durability and malleability.

Advertisement

1. 1

   Hold the flame 3–4 in (7.6–10.2 cm) from the copper you're annealing. Point the flame directly at the copper band or pipe. If you hold the flame much closer to the copper, you'll burn the metal's relatively delicate surface. Hold the flame farther than 4–5 inches (10–13 cm) away, and the copper will take a long time to heat.^[7]

   • The copper won't catch on fire. However, to avoid catching anything else in your work environment on fire, the copper should be on top of a non-flammable object like a piece of brick or concrete.
   • Always anneal copper in a well-ventilated area. Annealing copper produces chemicals that can harm your lungs if the room you're working in doesn't have proper ventilation.^[8]

2. 2

   Move the torch quickly back and forth above the surface of the copper. Keep the flame moving across the full surface of the copper to evenly heat it. It's important that you distribute the heat evenly, so no areas of the copper are annealed faster than any others. As you heat the surface of the copper, you'll notice that red and orange colors swirl across the metal's surface.^[9]

   • Have a dry chemical fire extinguisher in close proximity whenever you use an open flame. If any of the materials in your garage or metalworking lab catch on fire, spray them with the fire extinguisher immediately.

3. 3

   Spend extra time annealing thicker or heavier pieces of copper. The annealing process can work to soften any piece of copper, regardless of its thickness or size. However, the amount time that you'll need to heat the copper for will increase proportionately with the thickness of the copper.^[10]

   • For example, you may only need to heat a thin jewelry-grade piece of copper for 20 seconds to anneal it. For a heavy copper pipe or ¹⁄₂  in (1.3 cm) thick chunk of copper, you'll need to anneal for at least 2–3 minutes.

4. 4

   Keep the flame focused on the copper until it turns red. As you continue to heat the surface of the copper with your acetylene torch, it will turn black. Don't worry that you're burning the copper yet; it must turn black before it turns red. Continue moving the torch over the surface of the copper until the black color turns into a bright, glowing red. At this point, the copper is annealed.^[11]

   • Regardless of the size or thickness of the copper you're annealing, it will be fully annealed once it's glowing red.
   • Copper that is glowing cherry red is at the correct temperature for annealing purposes.

Advertisement

1. 1

   Turn the torch valves back to their closed position. Once the copper is annealed, you don't have any more need for the flame. Turn the acetylene valve counterclockwise to shut off the flow of gas. Then turn the oxygen valve back to its closed position as well. Turning the valves back to their closed positions will ensure that the flame is extinguished. At this point, you can remove your safety goggles.^[12]

   • Closing the acetylene valve first and the oxygen valve second will clear the torch of any acetylene.
   • Even when you're turning off the acetylene torch, be careful not to point it at any other people in your workspace.

2. 2

   Pick up the annealed copper with a pair of pliers. At this point, the copper will be incredibly hot, so you obviously cannot pick it up with your bare hands. So, slip 1 of the jaws of a pair of pliers under the edge of the copper bar or pipe, squeeze the pliers tightly shut, and pick up the annealed copper. ^[13] If you don't already have a pair of pliers, purchase a pair at a local hardware store.

   • You don't need to wear gloves at this point (or at any other point during the annealing process), since you'll never touch the metal directly until it's cool.
   • In a pinch, you could use a pair of ordinary tweezers to pick up the superheated copper. Just be careful not to drop it!

3. 3

   Deposit the annealed copper into a metal bucket of water. This will cause the red-hot copper to immediately lose heat and cool off. Keep an eye on the copper so you can gauge its temperature.^[14] Once the metal returns to its original reddish-brown color, use the pliers to remove the copper from the metal bucket.

   • The cooling process should take less than 5 minutes. Once this time has passed, the copper is now annealed and will be soft and malleable for working.
   • It's important that you use a metal bucket to cool the heated metal, since it could potentially melt through a plastic bucket.

Advertisement

Add New Question

• Question

  Can copper be annealed without water quenching? Is the quenching a way to work with it faster than waiting for it to cool in the air?

  

  Yeah. You do not have to quench it, but quenching also helps blow off some of the oxide that forms during annealing. Some alloys like all types of steel, and antimony/lead alloys harden if you quench them.

• Question

  Can I anneal copper tubing with a propane torch?

  

  Yes, but it will take much longer to get red hot compared to using MAP gas or oxy/acetylene.

• Question

  I heard that running my microwave with copper in it will remove any bad smells and stains. Is this true?

  

  No, it's not. Someone is trying to get you to damage your microwave. Microwaves work by exciting water particles, so a microwave actually will evaporate water. Microwaves would do nothing to the copper, except for produce sparks.

• Question

  Can I anneal any grade copper?

  

  Yes, but doing so changes the characteristics of the copper. Be careful, and make sure that the copper will still be within the parameters required for whatever job is expected of it. Also, not all copper products are pure copper, and those that aren't will react differently than those that are.

• Question

  Can I use a gas cylinder of LPG for heating copper?

  

  Assuming you mean using an LPG-fueled torch, yes, you just have to be able to heat the copper red hot.

• Question

  Can I use annealing with other metals like iron or nickel? If so, then what temperature?

  

  Nickel can be annealed using several different methods; the torch method is the least desirable since it heats unevenly and will form heavy oxidation on the surface. Open annealing of "pure" nickel is done from 1500 F to 1700 F. Leave it at that temperature for a while to fully soften so that crystals can reform. Note that different alloys of nickel have different annealing temps and will behave differently in a quench; "pure" nickel (nickel 200) will anneal while other alloys will harden or temper. Iron can also be annealed, at 1600 F - 1650 F, but it should be allowed to cool slowly afterwards rather than quenched.

• Question

  Should I always turn off acetylene before oxygen?

  

  Doesn't really matter. One benefit in turning the acetylene off first is that you avoid the soot produced from burning acetylene with too little O2.

• Question

  How do I return copper back to its hard state later after it is annealed?

  

  The process of hardening copper is called "work hardening". Bending, hammering, and tumbling in a tumbler are all methods of hardening the copper.

• Question

  How do I know if I need to anneal copper?

  

  Do you want it to be softer or harder? Harder is more brittle, softer is less brittle but easier to bend. Annealing lets all of the crystals in the metal reform, so they can be bend up again, till they are fragile, but harder again. It is a cycle you go through when you are cold forming something. (For making a copper rose, I pound on the copper till it gets hard to work, anneal it, then beat on it some more till I have what I want. If I could not anneal it, my arms would be much more worn out after the work. That is, I am not beating on it hot, it is room temperature, but after so many beatings, it gets hard and brittle, so I anneal it again.)

• Question

  Why can I quench ferrous metals, but not nonferrous metals? Why is it okay to quench copper, but not carbon steel?

  

  You can quench any metal through the act of plunging it into a bath of oil or water when it is hot. If you want to anneal it, though, you have to know what metal/alloy you are working with. You quench carbon steel to make it harder. It all has to do with how large the resulting crystalline structure is. Fast cooling results in a fine-grained structure, thus a hard but brittle material. Slow cooling allows the crystal grains to grow to a larger size, which results in a more malleable annealed steel. So, to anneal a hardened steel, you heat it red and then let it cool very slowly. It doesn't matter whether you quench copper, as just the act of heating it red anneals it.

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

Video

• Annealed copper can also be air-cooled instead of cooled by water. But, if you let the copper cool in the air, it will not be as soft and malleable after it has been annealed.

• If you're heating a very thin piece of copper, you could use an ordinary propane torch instead of the more heavy-duty acetylene torch.

• Annealing is the metallurgical term for heating a metal and subsequently cooling it to change its properties (such as its hardness or durability).

Thanks for submitting a tip for review!

Advertisement

• If you don't anneal the copper you're working with when it begins to become brittle, you'll risk fracturing or breaking the copper.^[16]

Advertisement

Things You'll Need

• Copper
• Oxygen acetylene torch
• Flint striker
• Safety goggles
• Brick
• Pliers
• Metal bucket
• Cold water
• Dry chemical fire extinguisher

About This Article

Article Summary X

Annealing copper makes it softer so you can bend it without breaking it. To anneal copper, you'll need to heat it with an acetylene torch until it glows red. Make sure you set your copper on an inflammable surface like a piece of brick or concrete so it doesn't catch fire. Light your acetylene torch and hold the flame 3 to 4 inches from the copper. Keep the flame moving over the surface to heat it evenly. You'll know it's annealed when it glows red. It should only take about 20 seconds for a thin piece of copper, but it could take 2 to 3 minutes for a thicker piece. Once your copper is glowing red, grip it with pliers and drop it into a metal bucket of water. Don't use a plastic bucket, since the copper could melt it. For more tips, including how to set up your acetylene torch, read on!

Did this summary help you?

Thanks to all authors for creating a page that has been read 212,941 times.

Did this article help you?

provenzanoworlse.blogspot.com

Source: https://www.wikihow.com/Anneal-Copper

Share this post